Ресивър за Домашно Кино Anthem AVM 50v 3D

15 199 лв.

7.1-канален процесор (предусилвател) за домашно кино.

7.1-channel A/V processor with Anthem Room Correction (ARC).

Описание

Anthem AVM 50v 3D

It’s now 3D equipped! Fully featured 7.1-channel audio and video processor, 8 HDMI Inputs and 2 Parallel HDMI outputs with the top four ports (HDMI 1 through 4) and top output (HDMI 1) supporting true bypass sensing 3D inputs automatically, Dolby TrueHD, DTS-HD Master Audio, PCM 24/192, highest quality 1080p upscaling with 1080p24 compatibility, Anthem Room Correction, two stereo zones.

From riding the third dimension on light cycles in the movie Tron, to racing through the 3D jungles of Pandora in Avatar, the movie experience is always better in triple dimensions. 3D video has a different structure than traditional video so it must pass through the A/V processor without being affected. The new Anthem AVM 50v circuit board automatically detects the presence of 3D video and go into passthrough mode as per a source menu option for video output configuration, passing the 3D HDMI signal from a 3D Blu-ray player to a 3D TV at resolutions up to 1080p. For additional convenience, in passthrough mode the output refresh rate is now automatically matched to the source’s frame refresh rate which is useful for sources that output a mix between 24, 50 and 60 Hz.

Sound from HDMI sources plays perfectly, at least if does if you’re using an AVM 50v. Why? In the AVM 50v, all eight HDMI inputs are connected through high-performance TMDS (Transition Minimized Differential Signaling) timing regenerators and multiplexers. The receiver contains a programmable equalizer and a Clock Data Recovery (CDR) function for each of the three TMDS pairs in an HDMI or DVI signal. The TMDS data outputs are regenerated and perfectly aligned to the regenerated TMDS clock signal, creating an extremely clean low-jitter DVI/HDMI signal that is easily decoded by the HDMI receiver. This is particularly useful for cleaning up a noisy/jittery source, or when a long or low-quality cable is being used.

Спецификация:
VIDEO SWITCHING
Bandwidth from input jack to output jack Composite and S-Video 70 MHz
Component: Y 110 MHz
Component: Pr 90 MHz
Component: Pb 80 MHz
All analog video inputs and outputs are 75 Ω, 1.5 Vp-p.
ANALOG AUDIO
Input Impedance 20 kΩ
Output Impedance Main–RCA 300 Ω
XLR 600 Ω
Zones 2/3 and Record 51 Ω
Rated Input 2.0 Vrms
Maximum Input 5.3 Vrms; 3.0 Vrms for 6-Ch input
Minimum Load 5 kΩ
Rated Output (100 kΩ load) 2.0 Vrms
Maximum Output RCA 6.3 Vrms
XLR 12.6 Vrms
Headphone Output 100 mW into 32 Ω at 0.2% THD+N
Volume Control Range Main -95.5 dB to +31.5 dB (in 0.5 dB increments)
Zones 2/3 and Headphone -62.5 dB to +10.0 dB (in 1.25 dB increments)
Crosstalk (at 1 kHz) 82 dB between channels; 86 dB between inputs
XLR Pin Configuration Pin 1: Ground, Pin 2: Positive, Pin 3: Negative
DIGITAL AUDIO
Crossover High-Pass Slope (small speaker setting) 12 dB/octave (2nd order)
Low-Pass Slope (subwoofer) 24 dB/octave (4th order)
Frequency (adjustable) 25 Hz to 160 Hz (in 5 Hz increments)
Tone Control Filter Type Shelf
Range ±12 dB
Bass Turnover Frequency 200 Hz
Treble Turnover Frequency 2 kHz
Analog-to-Digital Conversion S/N Ratio(at digital Rec output) (IEC-A Filter) 100 dB
All digital inputs and outputs comply with HDMI , S/PDIF or AES/EBU standards.
MAIN PATH (RCA and XLR Outputs)
Frequency Response and Bandwidth Analog Direct Inputs 10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 120 kHz (+0 -3 dB)
Analog-DSP Inputs at 24/96 10 Hz to 20 kHz (+0 -0.3 dB), 2 Hz to 37 kHz (+0 -3 dB)
Digital Inputs at 24/96 10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 39 kHz (+0 -3 dB)
THD+N (at Rated Input and Output) Analog Direct Inputs 0.006% (80 kHz BW)
Analog-DSP Inputs at 24/48 0.006% (AES17 Filter)
Digital Inputs at 24/48 0.004% (AES17 Filter)
IMD (CCIF at 15 kHz and 16 kHz) Analog Direct Inputs 0.001%
Analog-DSP Inputs at 24/48 0.003%
Digital Inputs at 24/48 0.001%
S/N Ratio (ref. 2.0 Vrms, IEC-A filter) Analog Direct Inputs 106 dB
Analog-DSP Inputs at 24/48 100 dB
Digital Inputs at 24/96 104 dB
ZONE 2 and ZONE 3 PATHS
Frequency Response and Bandwidth 20 Hz to 20 kHz (+0 -0.1 dB), 3 Hz to 140 kHz (+0, -3 dB)
THD+N (at Rated Input and Output) 0.06% (80 kHz BW)
IMD (CCIF at 15 kHz and 16 kHz) 0.06%
S/N Ratio (ref. 2.0 Vrms, IEC-A Filter) 97 dB
FM TUNER
Sensitivity 50 dB S/N 13 dBμ typical, 25 dBμ max
IHF 10 dBμ typical, 20 dBμ max
S/N Ratio Mono 75 dB typical, 65 dB min
Stereo 69 dB typical, 60 dB min
Distortion Mono 0.2% typical, 1.0% max
Stereo 0.3% typical, 1.5% max
Stereo Separation 40 dB typical, 25 dB min
Alternate Channel Selectivity (±400 kHz) 70 dB typical, 60 dB min
Frequency Response 25 Hz to 15 kHz (+0 -2 dB)
AM TUNER
Sensitivity (20 dB S/N) 49 dBμ typical, 56 dBμ max
S/N Ratio 50 dB typical, 43 dB min
Distortion 0.7% typical, 2.0% max
One-Signal Selectivity (±10 kHz) 24 dB typical, 18 dB min
CONTROL
Infra Red Carrier Frequency 38 kHz
Maximum 12 V Supply Current 150 mA
Maximum Emitter Current 60 mA per output
RS-232 Interface Connection DB-9F, straight-wired
Pinout (processor side) Pin 2: Tx, Pin 3: Rx, Pin 5: Ground
Baud Rate 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Configuration 8 data bits, 1 stop bit, no parity bits, flow control (RTS/CTS, none)
Trigger Outputs Polarity tip positive, sleeve ground
Maximum Current at 12 VDC 300 mA between all three triggers
Sequential Delay 250 ms
POWER REQUIREMENT
Power Consumption Maximum 150 W
DIMENSIONS (height includes feet)
Height 5-7/8 inches (14.9 cm) including feet; rack-mounting: 3 rack units without feet
Width 17-1/4 inches (43.8 cm)
Depth 14-1/2 inches (36.2 cm)
Weight (unpacked, not including 8 lb (3.5 kg) ARC microphone kit) 30.7 lb (14 kg)